Forgot Login?   Sign up  
Friday, November 22, 2024

Wow look at this monster traincar!!!!!!

More
12 years 8 months ago #13216 by Kelley
I just found this at Marsilus Trains newsletter..its on the bottom www.n-trains.de/news/1203back.pdf
If I was doing modern trains I would be itching for one of these things.
www.railpictures.net/viewphoto.php?id=364930&nseq=1
The newsletter says he will have one at Altenbeken to show.

Please Log in or Create an account to join the conversation.

More
12 years 8 months ago #13217 by stonysmith
Replied by stonysmith on topic Re: Wow look at this monster traincar!!!!!!
I worked a bit on it's smaller brother:


The trouble I ran into was the drawbar between the trucks. Using the various RP plastics, they're too thick to be proto or too brittle. I'm still searching for a workable concept.

Please Log in or Create an account to join the conversation.

More
12 years 8 months ago - 12 years 8 months ago #13226 by garthah
Replied by garthah on topic Re: Wow look at this monster traincar!!!!!!
Well maybe not a big or as heavey this is the car I built about a year ago for heavy hauling

cheerz Garth
Attachments:
The following user(s) said Thank You: southernnscale

Please Log in or Create an account to join the conversation.

More
12 years 1 month ago - 12 years 1 month ago #14352 by southernnscale
Replied by southernnscale on topic Re: Wow look at this monster traincar!!!!!!
do you have the Auran Trainz Program TS2009 or TS2012 ? If you do there is one like this not the same but its in the rolling stock in the program and it has several section to it. Its has 12 pieces to construct it.

Please Log in or Create an account to join the conversation.

More
7 years 11 months ago #18198 by kevsmith
Replied by kevsmith on topic Re: Wow look at this monster traincar!!!!!!
Well funny enough I have some of these at work. My team maintain six of these beasts designated KXA-C on TOPS



Fully loaded they top out at 166 tonne

With two bogies under each span bolster they'll go round a curve as tight as a dinner plate!




The previous versions were noted for being clad in stainless steel which upped the tare weight quite a bit. The new versions are stripped right down to get the payload as high as possible



Kev
The following user(s) said Thank You: southernnscale

Please Log in or Create an account to join the conversation.

More
7 years 11 months ago #18199 by southernnscale
Replied by southernnscale on topic Re: Wow look at this monster traincar!!!!!!
Yea! pretty cool looking! I have been trying to get a few of these cars! I have two I have 3D printed but the plastic is just to light to use as rolling stock but looks good sitting on a spur! the generater is also 3D printed.

Attachments:

Please Log in or Create an account to join the conversation.

More
7 years 11 months ago #18200 by southernnscale
Replied by southernnscale on topic Re: Wow look at this monster traincar!!!!!!
Here is the other I did 3D printed!

Attachments:

Please Log in or Create an account to join the conversation.

More
7 years 11 months ago #18201 by garthah
Replied by garthah on topic Re: Wow look at this monster traincar!!!!!!
Instead of trying to build span bolster in RP build a a shell to fit over either bar stock of Brass or Evergreen styrene as both can be drilled and tapped in addition the use of brass wire and rod can be used with either to enhance your detail

cheerz Garth

Please Log in or Create an account to join the conversation.

Time to create page: 0.269 seconds